View KD1084ADT-R_2329977.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/20 january 2004 typical dropout 1.3v (at 5a) three terminal adjustable or fixed output voltage 1.5v, 1.8v, 2.5v, 2.85v, 3.3v, 3.6v, 5v. guaranteed output current up to 5a ouput tolerance 1% at 25c and 2% in full temperature range for the "a" version ouput tolerance 2% at 25c and 3% in full temperature range internal power and thermal limit wide operating temperature range -40c to 125c package available: to-220, d 2 pak, d 2 pak/a, dpak pinout compatibility with standard adjustable vreg description the kd1084 is a low drop voltage regulator able to provide up to 5a of output current. dropout is guaranteed at a maximum of 1.5v at the maximum output current, decreasing at lower loads. the kd1084 is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance. a 2.85v output version is suitable for scsi-2 active termination. unlike pnp regulators, where a part of the output current is wasted as quiescent current, the kd1084 quiescent current flows into the load, so increase efficiency. only a 10f minimum capacitor is need for stability. the devices are supplied in to-220, d 2 pak, d 2 pak/a and dpak. on chip trimming allows the regulator to reach a very tight output voltage tolerance, within 1% at 25c for "a" version and 2% at 25c for standard version. kd1084 series 5a low drop positive voltage regulator adjustable and fixed schematic diagram to-220 d 2 pak d 2 pa k/a dpak
kd1084 series 2/20 absolute maximum ratings absolute maximum ratings are those values beyond which damage to the device may occur. functional operation under these condition is not implied. thermal data application circuits connection diagram (top view) symbol parameter value unit v i dc input voltage 12 v i o output current internally limited ma p d power dissipation internally limited mw t stg storage temperature range -55 to +150 c t op operating junction temperature range -40 to +125 c symbol parameter to-220 d 2 pak d 2 pak/a dpak unit r thj-case thermal resistance junction-case 333c/w r thj-amb thermal resistance junction-ambient 50 62.5 50 c/w r 2 v o =v ref (1 + ?? ) r 1 to-220 d 2 pak d 2 pak/a dpak
kd1084 series 3/20 ordering codes (*) available on request (**) available in tape & reel with the suffix "r" for fixed versions and "-r" for adjustable version electrical characteristics of kd1084a#15 (v i =4.5v, c i =c o =10 f (tant.), t a =-40to 125c, unless otherwise specified.) to-220 d 2 pak (**) d 2 pak/a (**) dpak (**) output voltage tolerance kd1084v15 (*) kd1084d2t15 kd1084d2m15 kd1084dt15 1.5 v 2% kd1084av15 (*) kd1084ad2t15 kd1084ad2m15 kd1084adt15 1.5 v 1% kd1084v18 kd1084d2t18 kd1084d2m18 kd1084dt18 1.8 v 2% kd1084av18 kd1084ad2t18 kd1084ad2m18 kd1084adt18 1.8 v 1% kd1084v25 kd1084d2t25 kd1084d2m25 kd1084dt25 2.5 v 2% kd1084av25 kd1084ad2t25 kd1084ad2m25 kd1084adt25 2.5 v 1% kd1084v28 (*) kd1084d2t28 (*) kd1084d2m28 (*) kd1084dt28 (*) 2.85 v 2% kd1084av28 (*) kd1084ad2t28 (*) kd1084ad2m28 (*) kd1084adt28 (*) 2.85 v 1% kd1084v33 kd1084d2t33 kd1084d2m33 kd1084dt33 3.3 v 2% kd1084av33 kd1084ad2t33 kd1084ad2m33 kd1084adt33 3.3 v 1% kd1084v36 kd1084d2t36 kd1084d2m36 kd1084dt36 3.6 v 2% kd1084av36 kd1084ad2t36 kd1084ad2m36 kd1084adt36 3.6 v 1% kd1084v50 kd1084d2t50 kd1084d2m50 kd1084dt50 5.0 v 2% kd1084av50 kd1084ad2t50 kd1084ad2m50 kd1084adt50 5.0 v 1% kd1084v kd1084d2t kd1084d2m kd1084dt adj 2% kd1084av kd1084ad2t kd1084ad2m kd1084adt adj 1% symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 1.485 1.5 1.515 v i o =0to5a v i = 3.1 to 10v 1.47 1.5 1.53 v ? v o line regulation i o =0ma v i = 3.1 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 3.1 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =5 1.5v 60 75 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 4/20 electrical characteristics of kd1084a#18 (v i =4.8v, c i =c o =10 f (tant.), t a =-40to 125c, unless otherwise specified.) electrical characteristics of kd1084a#25 (v i =5.5v, c i =c o =10 f (tant.), t a =-40to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 1.782 1.8 1.818 v i o =0to5a v i = 3.4 to 10v 1.764 1.8 1.836 v ? v o line regulation i o =0ma v i = 3.4 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 3.4 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =5.3 1.5v 60 75 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 % symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 2.475 2.5 2.525 v i o =0to5a v i = 4.1 to 10v 2.45 2.5 2.55 v ? v o line regulation i o =0ma v i = 4.1 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 4.1 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =6 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 5/20 electrical characteristics of kd1084a#285 (v i =5.85v, c i =c o =10 f(tant.),t a =-40to 125c, unless otherwise specified.) electrical characteristics of kd1084a#33 (v i =6.3v, c i =c o =10 f (tant.), t a =-40to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 2.821 2.85 2.879 v i o =0to5a v i = 4.5 to 10v 2.793 2.85 2.907 v ? v o line regulation i o =0ma v i = 4.5 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 4.5 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =6.35 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 % symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 3.267 3.3 3.333 v i o =0to5a v i = 4.9 to 10v 3.234 3.35 3.366 v ? v o line regulation i o =0ma v i = 4.9 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 4.9 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =6.8 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 6/20 electrical characteristics of kd1084a#36 (v i =6.6v, c i =c o =10 f (tant.), t a =-40to 125c, unless otherwise specified.) electrical characteristics of kd1084a#5 (v i =8v, c i =c o =10 f(tant.),t a = -40 to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 3.564 3.6 3.636 v i o =0to5a v i = 5.2 to 10v 3.528 3.6 3.672 v ? v o line regulation i o =0ma v i = 5.2 to 10v t j = 25c 0.5 10 mv i o =0ma v i = 5.2 to 10v 1 10 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =7.1 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 % symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j =25c 4.95 5 5.05 v i o =0to5a v i = 6.6 to 10v 4.9 5 5.1 v ? v o line regulation i o =0ma v i = 6.6 to 10v t j = 25c 0.5 10 mv i o =0ma v i = 6.6 to 10v 1 10 mv ? v o load regulation i o =0to5a t j =25c 5 20 mv i o = 0 to 5a 10 35 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =8.5 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 7/20 electrical characteristics of kd1084a (v i =4.25v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) electrical characteristics of kd1084#15 (v i =4.5v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 10ma t j = 25c 1.237 1.25 1.263 v i o = 10ma to 5a v i = 2.85 to 10v 1.225 1.25 1.275 v ? v o line regulation i o = 10ma v i =2.85to10v t j = 25c 0.015 0.2 % i o = 10ma v i = 2.85 to 10v 0.035 0.2 % ? v o load regulation i o = 10ma to 5a t j = 25c 0.1 0.3 % i o = 10ma to 5a 0.2 0.4 % v d dropout voltage i o =5a 1.3 1.5 v i o(min) minimum load current v i = 10v 3 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, c adj =25 f, i o =5a v i =4.75 1.5v 60 72 db i adj adjust pin current v i = 4.25v i o =10ma 55 120 a ? i adj adjust pin current change i o = 10ma to 5a v i = 2.85 to 10v 0.2 5 a en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 % symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 1.47 1.5 1.536 v i o =0to5a v i = 3.1 to 10v 1.455 1.5 1.545 v ? v o line regulation i o =0ma v i = 3.1 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 3.1 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =5 1.5v 60 75 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 8/20 electrical characteristics of kd1084#18 (v i =4.8v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) electrical characteristics of kd1084#25 (v i =5.5v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 1.764 1.8 1.836 v i o =0to5a v i = 3.4 to 10v 1.746 1.8 1.854 v ? v o line regulation i o =0ma v i = 3.4 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 3.4 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =5.3 1.5v 60 75 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 % symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 2.45 2.5 2.55 v i o =0to5a v i = 4.1 to 10v 2.425 2.5 2.575 v ? v o line regulation i o =0ma v i = 4.1 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 4.1 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =6 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 9/20 electrical characteristics of kd1084#285 (v i =5.85v, c i =c o =10 f (tant.), t a =-40to 125c, unless otherwise specified.) electrical characteristics of kd1084#33 (v i =6.3v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 2.793 2.85 2.907 v i o =0to5a v i = 4.5 to 10v 2.765 2.85 2.935 v ? v o line regulation i o =0ma v i = 4.5 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 4.5 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =6.35 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 % symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 3.234 3.3 3.366 v i o =0to5a v i = 4.9 to 10v 3.2 3.3 3.4 v ? v o line regulation i o =0ma v i = 4.9 to 10v t j = 25c 0.5 6 mv i o =0ma v i = 4.9 to 10v 1 6 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =6.8 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 10/20 electrical characteristics of kd1084#36 (v i =6.6v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) electrical characteristics of kd1084#5 (v i =8v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 3.528 3.6 3.672 v i o =0to5a v i = 5.2 to 10v 3.492 3.6 3.708 v ? v o line regulation i o =0ma v i = 5.2 to 10v t j = 25c 0.5 10 mv i o =0ma v i = 5.2 to 10v 1 10 mv ? v o load regulation i o =0to5a t j =25c 3 15 mv i o =0to5a 7 20 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =7.1 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 % symbol parameter test conditions min. typ. max. unit v o output voltage i o =0ma t j = 25c 4.9 5 5.1 v i o =0to5a v i = 6.6 to 10v 4.85 5 5.15 v ? v o line regulation i o =0ma v i = 6.6 to 10v t j = 25c 0.5 10 mv i o =0ma v i = 6.6 to 10v 1 10 mv ? v o load regulation i o =0to5a t j =25c 5 20 mv i o = 0 to 5a 10 35 v v d dropout voltage i o =5 a 1.3 1.5 v i q quiescent current v i 10v 5 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, i o =5a v i =8.5 1.5v 60 72 db en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 11/20 electrical characteristics of kd1084 (v i =4.25v, c i =c o =10 f (tant.), t a = -40 to 125c, unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 10ma t j = 25c 1.225 1.25 1.275 v i o = 10ma to 5a v i = 2.85 to 10v 1.213 1.25 1.287 v ? v o line regulation i o = 10ma v i =2.85to10v t j = 25c 0.015 0.2 % i o = 10ma v i = 2.85 to 10v 0.035 0.2 % ? v o load regulation i o = 10ma to 5a t j = 25c 1 0.3 % i o = 10ma to 5a 0.2 0.4 % v d dropout voltage i o =5a 1.3 1.5 v i o(min) minimum load current v i = 10v 3 10 ma i sc short circuit current v i -v o =5v 5.5 7 a thermal regulation t a = 25c, 30ms pulse 0.003 0.015 %/w svr supply voltage rejection f = 120 hz, c o =25 f, c adj =25 f, i o =5a v i =4.75 1.5v 60 72 db i adj adjust pin current v i = 4.25v i o =10ma 55 120 a ? i adj adjust pin current change i o = 10ma to 5a v i = 2.85 to 10v 0.2 5 a en rms output noise voltage (% of v o ) t a = 25c f =10hz to 10khz 0.003 % s temperature stability 0.5 % s long term stability t a = 125c 1000hrs 0.5 %
kd1084 series 12/20 typical characteristics (unless otherwise specified t j = 25c, c i =10 f (tant.), c o =10 f (tant.) figure 1 : dropout voltage vs output current figure 2 : dropout voltage vs temperature figure 3 : short circuit current vs dropout voltage figure 4 : line regulation vs temperature figure 5 : output voltage vs temperature figure 6 : load regulation vs temperature
kd1084 series 13/20 figure 7 : supply voltage rejection vs frequency figure 8 : adjust pin current vs output current figure 9 : line transient figure 10 : load transient v i =4 to 6v, i o =200ma,c i =1 f(tant), c o =10 f(tant), t s =t f =5 s v i =7 v, i o =0.1to5a,c i =1 f(tant), c o =10 f(tant) t s =t f =3.5 s
kd1084 series 14/20 dim. mm. inch min. typ max. min. typ. max. a 4.40 4.60 0.173 0.181 c 1.23 1.32 0.048 0.051 d 2.40 2.72 0.094 0.107 d1 1.27 0.050 e 0.49 0.70 0.019 0.027 f 0.61 0.88 0.024 0.034 f1 1.14 1.70 0.044 0.067 f2 1.14 1.70 0.044 0.067 g 4.95 5.15 0.194 0.203 g1 2.4 2.7 0.094 0.106 h2 10.0 10.40 0.393 0.409 l2 16.4 0.645 l4 13.0 14.0 0.511 0.551 l5 2.65 2.95 0.104 0.116 l6 15.25 15.75 0.600 0.620 l7 6.2 6.6 0.244 0.260 l9 3.5 3.93 0.137 0.154 dia. 3.75 3.85 0.147 0.151 to-220 mechanical dat a p011c
kd1084 series 15/20 dim. mm. inch min. typ max. min. typ. max. a 4.4 4.6 0.173 0.181 a1 2.49 2.69 0.098 0.106 a2 0.03 0.23 0.001 0.009 b 0.7 0.93 0.027 0.036 b2 1.14 1.7 0.044 0.067 c 0.45 0.6 0.017 0.023 c2 1.23 1.36 0.048 0.053 d 8.95 9.35 0.352 0.368 d1 8 0.315 e 10 10.4 0.393 0.409 e1 8.5 0.335 g 4.88 5.28 0.192 0.208 l 15 15.85 0.590 0.624 l2 1.27 1.4 0.050 0.055 l3 1.4 1.75 0.055 0.068 m 2.4 3.2 0.094 0.126 r 0.4 0.016 v2 0? 8? 0? 8? d 2 pak mec hanical data p011p6g
kd1084 series 16/20 dim. mm. inch min. typ max. min. typ. max. a 4.40 4.60 0.173 0.181 a1 2.49 2.69 0.098 0.106 b 0.7 0.93 0.027 0.036 b2 1.14 1.7 0.044 0.067 c 0.45 0.60 0.017 0.023 c2 1.21 1.36 0.047 0.053 d 8.95 9.35 0.352 0.368 e 10 10.4 0.393 0.409 g 4.88 5.28 0.192 0.208 l 15 15.85 0.590 0.106 l2 1.27 1.4 0.050 0.055 d 2 pak/a mecha nical data
kd1084 series 17/20 dim. mm. inch min. typ max. min. typ. max. a 2.2 2.4 0.086 0.094 a1 0.9 1.1 0.035 0.043 a2 0.03 0.23 0.001 0.009 b 0.64 0.9 0.025 0.035 b2 5.2 5.4 0.204 0.212 c 0.45 0.6 0.017 0.023 c2 0.48 0.6 0.019 0.023 d 6 6.2 0.236 0.244 d1 5.1 0.200 e 6.4 6.6 0.252 0.260 e1 4.7 0.185 e 2.28 0.090 e1 4.4 4.6 0.173 0.181 h 9.35 10.1 0.368 0.397 l 1 0.039 (l1) 2.8 0.110 l2 0.8 0.031 l4 0.6 1 0.023 0.039 dpak mechanical data 0068772-f
kd1084 series 18/20 dim. mm. inch min. typ max. min. typ. max. a 180 7.086 c 12.8 13.0 13.2 0.504 0.512 0.519 d 20.2 0.795 n 60 2.362 t 14.4 0.567 ao 10.50 10.6 10.70 0.413 0.417 0.421 bo 15.70 15.80 15.90 0.618 0.622 0.626 ko 4.80 4.90 5.00 0.189 0.193 0.197 po 3.9 4.0 4.1 0.153 0.157 0.161 p 11.9 12.0 12.1 0.468 0.472 0.476 ta pe & reel d 2 pak-p 2 pak-d 2 pak/a-p 2 pak/a mechanical data
kd1084 series 19/20 dim. mm. inch min. typ max. min. typ. max. a 330 12.992 c 12.8 13.0 13.2 0.504 0.512 0.519 d 20.2 0.795 n 60 2.362 t 22.4 0.882 ao 6.80 6.90 7.00 0.268 0.272 0.2.76 bo 10.40 10.50 10.60 0.409 0.413 0.417 ko 2.55 2.65 2.75 0.100 0.104 0.105 po 3.9 4.0 4.1 0.153 0.157 0.161 p 7.9 8.0 8.1 0.311 0.315 0.319 tape & reel dpak-ppak mechanical data
kd1084 series 20/20 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result f rom its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specificati ons mentioned in this publication are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectronics. the st logo is a registered trademark of stmicroelectronics all other names are the property of their respective owners ? 2004 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states. http://www.st.com

▲Up To Search▲

Price & Availability of KD1084ADT-R

	To Download KD1084ADT-R Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .